iT邦幫忙

0

CISCO 3500XL VLAN CREAT問題?網路達人幫幫忙!

  • 分享至 

  • xImage

CISCO 3500XL VLAN CREAT問題?CISCO 3500XL .24PORT的SWITCH IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5.3)W(1),flash:c3500XL-c3h2s-mz.120-5.3.WC.1.bin
1.新增一個VLAN 12(打上IP10.10.10.1 255.255.0.0)..下過shutdown no shutdown
2.VTP改Transparent
3.綁在FA0/1跟Fa/02..(多加了switchport trunk encapsulation dot1q)
下過shutdown no shutdown
4.為何界面都UP 但VLAN不行
VLAN12 is administratively down, line protocol is down不管是access mode 或TRUNK都不行?
5.但如把原本的VLAN 1就可(對接設備為2960..跳線平行線都不行)
6.(VLAN1綁IP 就可UP)請問那邊有設錯~? 謝謝
Switch#show run
interface FastEthernet0/1 switchport trunk allowed vlan 1,12,1002-1005
switchport mode trunk
interface FastEthernet0/2switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,12,1002-1005
switchport mode trunk
!interface VLAN12
ip address 10.10.10.1 255.255.0.0
no ip directed-broadcast no ip route-cache
shutdown
VLAN12 is administratively down, line protocol is down
Hardware is CPU Interface, address is 0030.94d4.b20(bia0030.94d4.b200)
Internet address is 10.10.10.1/16
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255Encapsulation ARPA
ARP type: ARPA, ARP Timeout 04:00:00
Switch#show int fa0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Fast Ethernet, address is 0030.94d4.b201 (bia 0030.94d4.b201)MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 180/255, txload 1/255, rxload 1/255
Switch#show int fa0/2
FastEthernet0/2 is up, line protocol is up
Hardware is Fast Ethernet, address is 0030.94d4.b202 (bia 0030.94d4.b202)MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set Auto-duplex (Full), Auto Speed (100), 100BaseTX/FX
(VLAN1綁IP 就可UP..自己新增的就是不行?)

圖片
  直播研討會
圖片
{{ item.channelVendor }} {{ item.webinarstarted }} |
{{ formatDate(item.duration) }}
直播中
4
stanshih
iT邦新手 5 級 ‧ 2011-01-18 11:16:03
最佳解答

先shutdown interface VLAN1,
再no shutdown interface VLAN12即可.

blue777 iT邦新手 5 級 ‧ 2011-01-18 22:19:02 檢舉

這是為何?因為我設其他台都ok

但就這一台不行~我還想是否ios有問題? 因為該做的都做了~我新增vlan12..就是無法讓他up...看唯一up的vlan1才綁過去vlan1就可正常會通可ping..但vlan12就是不行~但我的界面綁在FA0/1跟Fa/02界面確都up?但vlan不up確不通?

6
zackhuang
iT邦新手 2 級 ‧ 2011-01-16 16:19:26

看不懂你要問啥耶

2
新二君
iT邦新手 2 級 ‧ 2011-01-17 13:19:16

看不太懂你的提,但基本上要出這台機器才設trunk不然mode是access
如果要跟其他台switch交換vlan id才把連接那個port 設定為trunk
例如
conf t
inte fa 0/1
sw mode trunk
在設上要此透過此port的vlan 的id哪些或全部

我要發表回答

立即登入回答